Should I be using spdif 1.1 and 1.2 in mix control?ģ. Is my spdif wire correct? Belden 1694A Coaxial Digital Audio Cable, 6 foot, RCA/RCAĢ.
Yesterday the issue slowly fixed itself as I let everything rest. I then tried every combination of settings and nothing made the issue get better.
#Saffire mixcontrol bass boost pro
I then removed the pro 40 out to axe in just to eliminate a cable in the mix and assumed this would change nothing, which is what happened. If I strum the guitar, the sound fades up after a 1-3sec delay of silence (1-3sec after i strum) and intermittently cuts out and back in as the guitar is still ringing out. The levels on mix control spdif 1.1 and 1.2 were jumping up and down uncontrollably. I turned everything on with the settings I left yesterday and nothing worked right. I had limited time to test today but results were utterly frustrating. As I stated above, the sound quality is as if I went from the axe direct to the k12s. I did not try another unit with my axe to see if the spdif works as i have no other unit to test. If I left the volume on the guitar between 1-10 and simply had the guitar on the stand, there was a slight ambient noise from the guitar, almost silence but enough to have the popping not occur. Once the issue did subside, the only time it happened was when I had the volume on the guitar all the way at 0. Could it actually take some time for the clocks to sync? As I stated earlier, as I was typing my OP, the problem was starting to get better.Ģ. I will turn everything on tomorrow and take video.ġ. When the mix control reads no lock, the popping is crazy. I did also try the scenario at the end of your post. The wires I am using are brand new Belden 1694A Coaxial Digital Audio Cable, 6 foot, RCA/RCA, Orange from blue jeans cable.
Even just running the axe out to the saffire in with the other disconnected did not make a change. Tinkering with and swapping them did not change anything. I did swap the wires and checked the tightness of the connections. The sound of the guitar is fine when the clipping is not occurring. The scenario I listed in the OP is when playing into the axe so axe out to saffire in. (It should be flawless when everything works as intended.) The "No Lock" message shouldn't appear then, but this might not guarantee the signal is received flawlessly. This will allow the Saffire to be master. If there are other cables/electronics nearby, can you move the Axe/Saffire & SPDIF cable farther away from everything else?Īnother thing you could do is change the Axe-FX word clock parameter from auto to SPDIF/AES with both SPDIF cables connected, and set the Saffire sync source to Internal. Any details on what type of cables? Something labeled as being suitable for SPDIF vs. Jerry, have you tried a different SPDIF cable from Axe SPDIF out to Saffire SPDIF in? Since a Saffire Out - Axe In cable isn't needed for 1-way recording, try that cable for Axe Out - Saffire In. The OP isn't doing that though, with the settings described. When using SPDIF in on the Axe, the other device has to be the master. Did you determine if your Axe-FX SPDIF input works with any other device? No problems here reamping via SPDIF with a Saffire Pro 24. I'm not sure what else I can do to stop this from happening. I will note that as the pop is occurring the volume level bar in the mix control peaks to red as well. I then lower the volume to 0 on the guitar and the Lock to No Lock becomes more apparent. As I type this, the guitar sits on the stand with the volume all the way up and every so often it'll switch from Lock to No Lock giving off the popping.
As I fiddled with settings, jumping back and forth, it seemed to calm down only happening when I muted the strings on the guitar. When I turned it on today, it was happening almost uncontrollably. When I first turned the system on yesterday, the problem didn't seem to be there. The Sync Status will go from "Locked" to "No Lock" causing an annoying popping sound to come from the monitors. PRS CE22 plugged directly into INSTR on front panel of Axe-FXĪXE-FX is connected to USB of iMac (I've tested with the USB disconnected, no change) Logic Pro X (newest, but not open during these tests)Īxe-FX SPDIF IN to Pro 40 OUT, Axe-FX SPDIF OUT to Pro 40 IN I feel like I've scoured the internet for an answer and though I found many to get me to where I am now with my setup, there is one lingering problem I can't seem to figure out.
0 kommentar(er)
